Arresters For Protection Of Power Supply Systems Up To 1000 V I

PIV is lightning arrester type 1 according to EN 61643-11 and IEC 61643-1. These arresters are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 0 - 1 (according to IEC 1312-1 and EN 62305) for lightning current equipotential bonding and elimination of switching surges that originate in power supply systems entering the building.

The PIV is mainly intended for use in TNC systems. For TNS and TT systems it is necessary to combine these arresters with lightning arrester B25, B50 or B80 which are intended for equipotential bonding between N and PE.

The main use of PIV12,5 arrester is in structures of LPL III - IV according to EN 62305, e.g. residential houses with cable supply and subdistribution boards of big industrial structures.

Function of remote monitor terminals

When the PIV DS is operating correctly, the terminations 1-2 are connected to normally closed contacts, 2-3 are normally open. If the internal varistor component is damaged as a result of thermal overloading, terminations 1-2 will then be open and 2-3 closed.

HS50-50 DS is a lightning arrester type 1 according to EN 61643-11. These are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 0 – 1 (according to IEC 1312-1 and EN 62305) for lightning current equipotential bonding in power supply systems entering the building.

The lightning arrester is constructed as an encapsulated multiple spark gap for installation in main switchboards. HS50-50 DS is mainly intended for use in TNC systems. For TNS and TT systems it is necessary to combine these arresters with lightning arrester HS100 (or JK110) which is intended for equipotential bonding between N and PE.

The main use of HS50-50 DS is in industrial installations such as transformers, the main switchboards of large industrial buildings and places with high risk of a direct lightning strike. It is also suitable
for applications in unmeasured parts of electrical installation (before electrometer) according to VDN Directive, 2nd Edition 2004 (TAB 2000).
This model is equipped with red & green LED diodes signalising the right HS function as well as remote control failure signalisation by inbuilt optoelectronics with open collector output.

Function of remote control terminals
When the HS50-50 DS is operating correctly, the output transistor of inbuilt remote control is open. Once the internal ignishing HS circuit is broken, this output transistor is switched.

SPC is lightning and surge arrester type 1+2 according to EN 61643-11. These are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 0 – 1 (according to IEC 1312-1 and EN 62305) for lightning current equipotential bonding and elimination of switching surges that originate in power supply systems entering the building.

The SPC 12,5 is intended for use in TNC systems (1+0 or 3+0). For TNS and TT systems (1+1 or 3+1) the SPC 12,5 is equipped with high energy gas discharge tube for equipotential bonding between N and PE.

The main use of SPC12,5 arrester is in structures of LPL II according to EN 62305, e.g. industrial and administration buildings, schools, supermarkets and cathedrals.

Function of remote monitor terminals

When the SPC12,5 DS is operating correctly, the terminations 1-2 are connected to normally closed contacts, 2-3 are normally open. If the internal varistor component is damaged as a result of thermal overloading, terminations 1-2 will then be open and 2-3 closed.

The SPC25 is intended for use in TNC systems (1+0 or 3+0). For TNS and TT systems (1+1 or 3+1) the SPC25 is equipped with high energy gas discharge tube for equipotential bonding between N and PE.

The main use of SPC25 arrester is in structures of LPL I according to EN 62305, e.g. hospitals, banks, mobile operator stations, water-stations, power plants, airport buildings for air traffic control and all structures with explosive risk.

To be installed in the main switchboard.

Function of remote monitor terminals

When the SPC25 DS is operating correctly, the terminations 1-2 are connected to normally closed contacts, 2-3 are normally open. If the internal varistor component is damaged as a result of thermal overloading, terminations 1-2 will then be open and 2-3 closed.

SPC is lightning and surge arrester type 1+2 according to EN 61643-11. These are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 0 – 1 (according to IEC 1312-1 and EN 62305) for lightning current equipotential bonding and elimination of switching surges that originate in power supply systems entering the building.

The SPC 12,5 is intended for use in TNC systems (1+0 or 3+0). For TNS and TT systems (1+1 or 3+1) the SPC 12,5 is equipped with high energy gas discharge tube for equipotential bonding between N and PE.

The main use of SPC12,5 arrester is in structures of LPL II according to EN 62305, e.g. industrial and administration buildings, schools, supermarkets and cathedrals.

Function of remote monitor terminals

When the SPC12,5 DS is operating correctly, the terminations 1-2 are connected to normally closed contacts, 2-3 are normally open. If the internal varistor component is damaged as a result of thermal overloading, terminations 1-2 will then be open and 2-3 closed.

The SPC25 is intended for use in TNC systems (1+0 or 3+0). For TNS and TT systems (1+1 or 3+1) the SPC25 is equipped with high energy gas discharge tube for equipotential bonding between N and PE.

The main use of SPC25 arrester is in structures of LPL I according to EN 62305, e.g. hospitals, banks, mobile operator stations, water-stations, power plants, airport buildings for air traffic control and all structures with explosive risk.

To be installed in the main switchboard.

Function of remote monitor terminals

When the SPC25 DS is operating correctly, the terminations 1-2 are connected to normally closed contacts, 2-3 are normally open. If the internal varistor component is damaged as a result of thermal overloading, terminations 1-2 will then be open and 2-3 closed.

SPC is lightning and surge arrester type 1+2 according to EN 61643-11. These are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 0 – 1 (according to IEC 1312-1 and EN 62305) for lightning current equipotential bonding and elimination of switching surges that originate in power supply systems entering the building.

The SPC 12,5 is intended for use in TNC systems (1+0 or 3+0). For TNS and TT systems (1+1 or 3+1) the SPC 12,5 is equipped with high energy gas discharge tube for equipotential bonding between N and PE.

The main use of SPC12,5 arrester is in structures of LPL II according to EN 62305, e.g. industrial and administration buildings, schools, supermarkets and cathedrals.

Function of remote monitor terminals

When the SPC12,5 DS is operating correctly, the terminations 1-2 are connected to normally closed contacts, 2-3 are normally open. If the internal varistor component is damaged as a result of thermal overloading, terminations 1-2 will then be open and 2-3 closed.

It was designed to protection of positive & negative busbars of photo volatic systems aganist the surge effects.

The SPC25 is intended for use in TNC systems (1+0 or 3+0). For TNS and TT systems (1+1 or 3+1) the SPC25 is equipped with high energy gas discharge tube for equipotential bonding between N and PE.

The main use of SPC25 arrester is in structures of LPL I according to EN 62305, e.g. hospitals, banks, mobile operator stations, water-stations, power plants, airport buildings for air traffic control and all structures with explosive risk.

To be installed in the main switchboard.

Function of remote monitor terminals

When the SPC25 DS is operating correctly, the terminations 1-2 are connected to normally closed contacts, 2-3 are normally open. If the internal varistor component is damaged as a result of thermal overloading, terminations 1-2 will then be open and 2-3 closed.

SPC is lightning and surge arrester type 1+2 according to EN 61643-11. These are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 0 – 1 (according to IEC 1312-1 and EN 62305) for lightning current equipotential bonding and elimination of switching surges that originate in power supply systems entering the building.

The SPC 12,5 is intended for use in TNC systems (1+0 or 3+0). For TNS and TT systems (1+1 or 3+1) the SPC 12,5 is equipped with high energy gas discharge tube for equipotential bonding between N and PE.

The main use of SPC12,5 arrester is in structures of LPL II according to EN 62305, e.g. industrial and administration buildings, schools, supermarkets and cathedrals.

Function of remote monitor terminals

When the SPC12,5 DS is operating correctly, the terminations 1-2 are connected to normally closed contacts, 2-3 are normally open. If the internal varistor component is damaged as a result of thermal overloading, terminations 1-2 will then be open and 2-3 closed.

SPC is lightning and surge arrester type 1+2 according to EN 61643-11. These are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 0 – 1 (according to IEC 1312-1 and EN 62305) for lightning current equipotential bonding and elimination of switching surges that originate in power supply systems entering the building.

The SPC 12,5 is intended for use in TNC systems (1+0 or 3+0). For TNS and TT systems (1+1 or 3+1) the SPC 12,5 is equipped with high energy gas discharge tube for equipotential bonding between N and PE.

The main use of SPC12,5 arrester is in structures of LPL II according to EN 62305, e.g. industrial and administration buildings, schools, supermarkets and cathedrals.

Hakel Combi Set is lightning and surge arrester type 1+2 according to EN 61643-11 and IEC 61643-1. These are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 0 – 2 (according to IEC 1312-1 and EN 62305) for lightning current equipotential bonding and elimination of switching surges that originate in power supply systems entering the building.
Hakel Combi Set is a combination of the latest technologies where the spark gap combines the varistor. The set contains lightning arresters of HS series and surge arresters of PIII series. HCS can be installed in every common switchboard and its special construction is intended for using in non-measurable parts of electrical systems.

HCS/3+0 can be used in industrial installations such as substations, main switchboards of large industrial structures and also places with high risk of a direct lightning strikes occurance. This device is intended for use in TNC power supply system.

SPC is lightning and surge arrester type 1+2 according to EN 61643-11. These are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 0 – 1 (according to IEC 1312-1 and EN 62305) for lightning current equipotential bonding and elimination of switching surges that originate in power supply systems entering the building.

The SPC 12,5 is intended for use in TNC systems (1+0 or 3+0). For TNS and TT systems (1+1 or 3+1) the SPC 12,5 is equipped with high energy gas discharge tube for equipotential bonding between N and PE.

The main use of SPC12,5 arrester is in structures of LPL II according to EN 62305, e.g. industrial and administration buildings, schools, supermarkets and cathedrals.

Function of remote monitor terminals

When the SPC12,5 DS is operating correctly, the terminations 1-2 are connected to normally closed contacts, 2-3 are normally open. If the internal varistor component is damaged as a result of thermal overloading, terminations 1-2 will then be open and 2-3 closed.

SPC is lightning and surge arrester type 1+2 according to EN 61643-11. These are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 0 – 1 (according to IEC 1312-1 and EN 62305) for lightning current equipotential bonding and elimination of switching surges that originate in power supply systems entering the building.

The SPC 12,5 is intended for use in TNC systems (1+0 or 3+0). For TNS and TT systems (1+1 or 3+1) the SPC 12,5 is equipped with high energy gas discharge tube for equipotential bonding between N and PE.

The main use of SPC12,5 arrester is in structures of LPL II according to EN 62305, e.g. industrial and administration buildings, schools, supermarkets and cathedrals.

The SPC25 is intended for use in TNC systems (1+0 or 3+0). For TNS and TT systems (1+1 or 3+1) the SPC25 is equipped with high energy gas discharge tube for equipotential bonding between N and PE.

The main use of SPC25 arrester is in structures of LPL I according to EN 62305, e.g. hospitals, banks, mobile operator stations, water-stations, power plants, airport buildings for air traffic control and all structures with explosive risk.

To be installed in the main switchboard.

Function of remote monitor terminals

When the SPC25 DS is operating correctly, the terminations 1-2 are connected to normally closed contacts, 2-3 are normally open. If the internal varistor component is damaged as a result of thermal overloading, terminations 1-2 will then be open and 2-3 closed.

The SPC25 is intended for use in TNC systems (1+0 or 3+0). For TNS and TT systems (1+1 or 3+1) the SPC25 is equipped with high energy gas discharge tube for equipotential bonding between N and PE.

The main use of SPC25 arrester is in structures of LPL I according to EN 62305, e.g. hospitals, banks, mobile operator stations, water-stations, power plants, airport buildings for air traffic control and all structures with explosive risk.

To be installed in the main switchboard.

SPC is lightning and surge arrester type 1+2 according to EN 61643-11. These are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 0 – 1 (according to IEC 1312-1 and EN 62305) for lightning current equipotential bonding and elimination of switching surges that originate in power supply systems entering the building.

The SPC 12,5 is intended for use in TNC systems (1+0 or 3+0). For TNS and TT systems (1+1 or 3+1) the SPC 12,5 is equipped with high energy gas discharge tube for equipotential bonding between N and PE.

The main use of SPC12,5 arrester is in structures of LPL II according to EN 62305, e.g. industrial and administration buildings, schools, supermarkets and cathedrals.

SPC is lightning and surge arrester type 1+2 according to EN 61643-11. These are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 0 – 1 (according to IEC 1312-1 and EN 62305) for lightning current equipotential bonding and elimination of switching surges that originate in power supply systems entering the building.

The SPC 12,5 is intended for use in TNC systems (1+0 or 3+0). For TNS and TT systems (1+1 or 3+1) the SPC 12,5 is equipped with high energy gas discharge tube for equipotential bonding between N and PE.

The main use of SPC12,5 arrester is in structures of LPL II according to EN 62305, e.g. industrial and administration buildings, schools, supermarkets and cathedrals.

The SPC25 is intended for use in TNC systems (1+0 or 3+0). For TNS and TT systems (1+1 or 3+1) the SPC25 is equipped with high energy gas discharge tube for equipotential bonding between N and PE.

The main use of SPC25 arrester is in structures of LPL I according to EN 62305, e.g. hospitals, banks, mobile operator stations, water-stations, power plants, airport buildings for air traffic control and all structures with explosive risk.

To be installed in the main switchboard.

SPC is lightning and surge arrester type 1+2 according to EN 61643-11. These are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 0 – 1 (according to IEC 1312-1 and EN 62305) for lightning current equipotential bonding and elimination of switching surges that originate in power supply systems entering the building.

The SPC 12,5 is intended for use in TNC systems (1+0 or 3+0). For TNS and TT systems (1+1 or 3+1) the SPC 12,5 is equipped with high energy gas discharge tube for equipotential bonding between N and PE.

The main use of SPC12,5 arrester is in structures of LPL II according to EN 62305, e.g. industrial and administration buildings, schools, supermarkets and cathedrals.

SPC is lightning and surge arrester type 1+2 according to EN 61643-11. These are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 0 – 1 (according to IEC 1312-1 and EN 62305) for lightning current equipotential bonding and elimination of switching surges that originate in power supply systems entering the building.

The SPC 12,5 is intended for use in TNC systems (1+0 or 3+0). For TNS and TT systems (1+1 or 3+1) the SPC 12,5 is equipped with high energy gas discharge tube for equipotential bonding between N and PE.

The main use of SPC12,5 arrester is in structures of LPL II according to EN 62305, e.g. industrial and administration buildings, schools, supermarkets and cathedrals.

Function of remote monitor terminals

When the SPC12,5 DS is operating correctly, the terminations 1-2 are connected to normally closed contacts, 2-3 are normally open. If the internal varistor component is damaged as a result of thermal overloading, terminations 1-2 will then be open and 2-3 closed.

SPC is lightning and surge arrester type 1+2 according to EN 61643-11. These are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 0 – 1 (according to IEC 1312-1 and EN 62305) for lightning current equipotential bonding and elimination of switching surges that originate in power supply systems entering the building.

The SPC 12,5 is intended for use in TNC systems (1+0 or 3+0). For TNS and TT systems (1+1 or 3+1) the SPC 12,5 is equipped with high energy gas discharge tube for equipotential bonding between N and PE.

The main use of SPC12,5 arrester is in structures of LPL II according to EN 62305, e.g. industrial and administration buildings, schools, supermarkets and cathedrals.

SPC is lightning and surge arrester type 1+2 according to EN 61643-11. These are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 0 – 1 (according to IEC 1312-1 and EN 62305) for lightning current equipotential bonding and elimination of switching surges that originate in power supply systems entering the building.

The SPC 12,5 is intended for use in TNC systems (1+0 or 3+0). For TNS and TT systems (1+1 or 3+1) the SPC 12,5 is equipped with high energy gas discharge tube for equipotential bonding between N and PE.

The main use of SPC12,5 arrester is in structures of LPL II according to EN 62305, e.g. industrial and administration buildings, schools, supermarkets and cathedrals.

The SPC25 is intended for use in TNC systems (1+0 or 3+0). For TNS and TT systems (1+1 or 3+1) the SPC25 is equipped with high energy gas discharge tube for equipotential bonding between N and PE.

The main use of SPC25 arrester is in structures of LPL I according to EN 62305, e.g. hospitals, banks, mobile operator stations, water-stations, power plants, airport buildings for air traffic control and all structures with explosive risk.

To be installed in the main switchboard.

PIVM is modular lightning arrester type 1 according to EN 61643-11. Complete device consist of a base part and pluggable module. These arresters are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 0 - 1 (according to IEC 1312-1 and EN 62305) for lightning current equipotential bonding and elimination of switching surges that originate in power supply systems entering the building.

The PIVM is mainly intended for use in TNC systems. For TNS and TT systems it is necessary to combine these arresters with lightning arrester B25, B25M or B50 which are intended for equipotential bonding between N and PE.

The main use of PIVM7 arrester is in structures of LPL III - IV according to EN 62305, e.g. residential houses with cable supply and subdistribution boards of big industrial structures.

PIVM is modular lightning arrester type 1 according to EN 61643-11. Complete device consist of a base part and pluggable module. These arresters are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 0 - 1 (according to IEC 1312-1 and EN 62305) for lightning current equipotential bonding and elimination of switching surges that originate in power supply systems entering the building.

The PIVM is mainly intended for use in TNC systems. For TNS and TT systems it is necessary to combine these arresters with lightning arrester B25, B25M or B50 which are intended for equipotential bonding between N and PE.

The main use of PIVM7 arrester is in structures of LPL III - IV according to EN 62305, e.g. residential houses with cable supply and subdistribution boards of big industrial structures.

Function of remote monitor terminals

When the PIVM DS is operating correctly, the terminations 1-2 are connected to normally closed contacts, 2-3 are normally open. If the internal varistor component is damaged as a result of thermal overloading, terminations 1-2 will then be open and 2-3 closed.

PIVM is modular lightning arrester type 1 according to EN 61643-11. Complete device consist of a base part and pluggable module. These arresters are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 0 - 1 (according to IEC 1312-1 and EN 62305) for lightning current equipotential bonding and elimination of switching surges that originate in power supply systems entering the building.

The PIVM is mainly intended for use in TNC systems. For TNS and TT systems it is necessary to combine these arresters with lightning arrester B25, B25M or B50 which are intended for equipotential bonding between N and PE.

The main use of PIVM7 arrester is in structures of LPL III - IV according to EN 62305, e.g. residential houses with cable supply and subdistribution boards of big industrial structures.

PIVM is modular lightning arrester type 1 according to EN 61643-11. Complete device consist of a base part and pluggable module. These arresters are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 0 - 1 (according to IEC 1312-1 and EN 62305) for lightning current equipotential bonding and elimination of switching surges that originate in power supply systems entering the building.

The PIVM is mainly intended for use in TNC systems. For TNS and TT systems it is necessary to combine these arresters with lightning arrester B25, B25M or B50 which are intended for equipotential bonding between N and PE.

The main use of PIVM7 arrester is in structures of LPL III - IV according to EN 62305, e.g. residential houses with cable supply and subdistribution boards of big industrial structures.

PIVM is modular lightning arrester type 1 according to EN 61643-11. Complete device consist of a base part and pluggable module. These arresters are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 0 - 1 (according to IEC 1312-1 and EN 62305) for lightning current equipotential bonding and elimination of switching surges that originate in power supply systems entering the building.

The PIVM is mainly intended for use in TNC systems. For TNS and TT systems it is necessary to combine these arresters with lightning arrester B25, B25M or B50 which are intended for equipotential bonding between N and PE.

The main use of PIVM7 arrester is in structures of LPL III - IV according to EN 62305, e.g. residential houses with cable supply and subdistribution boards of big industrial structures.

PIVM is modular lightning arrester type 1 according to EN 61643-11. Complete device consist of a base part and pluggable module. These arresters are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 0 - 1 (according to IEC 1312-1 and EN 62305) for lightning current equipotential bonding and elimination of switching surges that originate in power supply systems entering the building.

The PIVM is mainly intended for use in TNC systems. For TNS and TT systems it is necessary to combine these arresters with lightning arrester B25, B25M or B50 which are intended for equipotential bonding between N and PE.

The main use of PIVM7 arrester is in structures of LPL III - IV according to EN 62305, e.g. residential houses with cable supply and subdistribution boards of big industrial structures.

PIVM is modular lightning arrester type 1 according to EN 61643-11. Complete device consist of a base part and pluggable module. These arresters are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 0 - 1 (according to IEC 1312-1 and EN 62305) for lightning current equipotential bonding and elimination of switching surges that originate in power supply systems entering the building.

The PIVM is mainly intended for use in TNC systems. For TNS and TT systems it is necessary to combine these arresters with lightning arrester B25, B25M or B50 which are intended for equipotential bonding between N and PE.

The main use of PIVM7 arrester is in structures of LPL III - IV according to EN 62305, e.g. residential houses with cable supply and subdistribution boards of big industrial structures.

Function of remote monitor terminals

When the PIVM DS is operating correctly, the terminations 1-2 are connected to normally closed contacts, 2-3 are normally open. If the internal varistor component is damaged as a result of thermal overloading, terminations 1-2 will then be open and 2-3 closed.

PIVM is modular lightning arrester type 1 according to EN 61643-11. Complete device consist of a base part and pluggable module. These arresters are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 0 - 1 (according to IEC 1312-1 and EN 62305) for lightning current equipotential bonding and elimination of switching surges that originate in power supply systems entering the building.

The PIVM is mainly intended for use in TNC systems. For TNS and TT systems it is necessary to combine these arresters with lightning arrester B25, B25M or B50 which are intended for equipotential bonding between N and PE.

The main use of PIVM7 arrester is in structures of LPL III - IV according to EN 62305, e.g. residential houses with cable supply and subdistribution boards of big industrial structures.

Function of remote monitor terminals

When the PIVM DS is operating correctly, the terminations 1-2 are connected to normally closed contacts, 2-3 are normally open. If the internal varistor component is damaged as a result of thermal overloading, terminations 1-2 will then be open and 2-3 closed.

PIVM is modular lightning arrester type 1 according to EN 61643-11. Complete device consist of a base part and pluggable module. These arresters are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 0 - 1 (according to IEC 1312-1 and EN 62305) for lightning current equipotential bonding and elimination of switching surges that originate in power supply systems entering the building.

The PIVM is mainly intended for use in TNC systems. For TNS and TT systems it is necessary to combine these arresters with lightning arrester B25, B25M or B50 which are intended for equipotential bonding between N and PE.

The main use of PIVM7 arrester is in structures of LPL III - IV according to EN 62305, e.g. residential houses with cable supply and subdistribution boards of big industrial structures.

Function of remote monitor terminals

When the PIVM DS is operating correctly, the terminations 1-2 are connected to normally closed contacts, 2-3 are normally open. If the internal varistor component is damaged as a result of thermal overloading, terminations 1-2 will then be open and 2-3 closed.

PIVM is modular lightning arrester type 1 according to EN 61643-11. Complete device consist of a base part and pluggable module. These arresters are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 0 - 1 (according to IEC 1312-1 and EN 62305) for lightning current equipotential bonding and elimination of switching surges that originate in power supply systems entering the building.

The PIVM is mainly intended for use in TNC systems. For TNS and TT systems it is necessary to combine these arresters with lightning arrester B25, B25M or B50 which are intended for equipotential bonding between N and PE.

The main use of PIVM7 arrester is in structures of LPL III - IV according to EN 62305, e.g. residential houses with cable supply and subdistribution boards of big industrial structures.

Function of remote monitor terminals

When the PIVM DS is operating correctly, the terminations 1-2 are connected to normally closed contacts, 2-3 are normally open. If the internal varistor component is damaged as a result of thermal overloading, terminations 1-2 will then be open and 2-3 closed.

PIVM is modular lightning arrester type 1 according to EN 61643-11. Complete device consist of a base part and pluggable module. These arresters are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 0 - 1 (according to IEC 1312-1 and EN 62305) for lightning current equipotential bonding and elimination of switching surges that originate in power supply systems entering the building.

The PIVM is mainly intended for use in TNC systems. For TNS and TT systems it is necessary to combine these arresters with lightning arrester B25, B25M or B50 which are intended for equipotential bonding between N and PE.

The main use of PIVM7 arrester is in structures of LPL III - IV according to EN 62305, e.g. residential houses with cable supply and subdistribution boards of big industrial structures.

PIVM is modular lightning arrester type 1 + type 2 according to EN 61643-11 and IEC 61643-1. Complete device consists of a base part and pluggable module. These arresters are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 0 - 1 (according to IEC 1312-1 and EN 62305) for lightning current equipotential bonding and elimination of switching surges that originate in power supply systems entering the building.

The PIVM is mainly intended for use in TNC systems. For TNS and TT systems it is necessary to combine these arresters with lightning arrester B25, B25M or B50 which are intended for equipotential bonding between N and PE.

The main use of PIVM7 arrester is in structures of LPL III - IV according to EN 62305, e.g. residential houses with cable supply and subdistribution boards of big industrial structures.

PIVM is modular lightning arrester type 1 + type 2 according to EN 61643-11 and IEC 61643-1. Complete device consists of a base part and pluggable module. These arresters are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 0 - 1 (according to IEC 1312-1 and EN 62305) for lightning current equipotential bonding and elimination of switching surges that originate in power supply systems entering the building.

The PIVM is mainly intended for use in TNC systems. For TNS and TT systems it is necessary to combine these arresters with lightning arrester B25, B25M or B50 which are intended for equipotential bonding between N and PE.

The main use of PIVM7 arrester is in structures of LPL III - IV according to EN 62305, e.g. residential houses with cable supply and subdistribution boards of big industrial structures.

PIVM is modular lightning arrester type 1 + type 2 according to EN 61643-11 and IEC 61643-1. Complete device consists of a base part and pluggable module. These arresters are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 0 - 1 (according to IEC 1312-1 and EN 62305) for lightning current equipotential bonding and elimination of switching surges that originate in power supply systems entering the building.

The PIVM is mainly intended for use in TNC systems. For TNS and TT systems it is necessary to combine these arresters with lightning arrester B25, B25M or B50 which are intended for equipotential bonding between N and PE.

The main use of PIVM7 arrester is in structures of LPL III - IV according to EN 62305, e.g. residential houses with cable supply and subdistribution boards of big industrial structures.

PIVM is modular lightning arrester type 1 + type 2 according to EN 61643-11 and IEC 61643-1. Complete device consists of a base part and pluggable module. These arresters are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 0 - 1 (according to IEC 1312-1 and EN 62305) for lightning current equipotential bonding and elimination of switching surges that originate in power supply systems entering the building.

The PIVM is mainly intended for use in TNC systems. For TNS and TT systems it is necessary to combine these arresters with lightning arrester B25, B25M or B50 which are intended for equipotential bonding between N and PE.

The main use of PIVM7 arrester is in structures of LPL III - IV according to EN 62305, e.g. residential houses with cable supply and subdistribution boards of big industrial structures.

PIVM is modular lightning arrester type 1 + type 2 according to EN 61643-11 and IEC 61643-1. Complete device consists of a base part and pluggable module. These arresters are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 0 - 1 (according to IEC 1312-1 and EN 62305) for lightning current equipotential bonding and elimination of switching surges that originate in power supply systems entering the building.

The PIVM is mainly intended for use in TNC systems. For TNS and TT systems it is necessary to combine these arresters with lightning arrester B25, B25M or B50 which are intended for equipotential bonding between N and PE.

The main use of PIVM7 arrester is in structures of LPL III - IV according to EN 62305, e.g. residential houses with cable supply and subdistribution boards of big industrial structures.

Function of remote monitor terminals

When the PIVM DS is operating correctly, the terminations 1-2 are connected to normally closed contacts, 2-3 are normally open. If the internal varistor component is damaged as a result of thermal overloading, terminations 1-2 will then be open and 2-3 closed.